Playlists werden geladen.. Since the wires are almost always made of copper, people usually speak of fiber vs. The original 3 MBps Ethernet developed by Xerox in the 1. Ohm RG- 8/U coax cable. Later a version using the thinner RG- 5. Ohm coax was introduced. Eventually several different standards emerged which used twisted- pair cabling. The . The twist is important for properly carrying electrical signals down the wires, for several reasons. This produces less signal distortion, especially at higher frequencies. The wires act like antennas, so they send and receive electro- magnetic waves; if two wires are next to each other, a signal on one will be picked up by the other. The twist reduces this. Twisted- pair cables can be either STP (shielded twisted pair) and UTP (unshielded twisted pair). As the name implies, STP adds a conductive layer (typically metal foil) surrounding either each pair or the entire cable. This shielding helps reduce interference from electrical sources outside the cable. If the individual paris are shielded, this also reduces crosstalk. All About Cat 6A Cat 6A Shielded Cable. Cat 6A shielded twisted pair. The shield of the STP cable is bonded to the patch panel during termination. Published: August 2004. In an STP cable, cable pairs (not individual wires). CAT-5, CAT-5e, CAT-6, CAT-7 Patch Cables FAQs. What is the difference between CAT-5. What is the difference between the types of cable - UTP, Patch, Stranded. Look at the cable connecting your telephone to the wall. Assuming this is a conventional analog system like you would find at home (not a digital PBX or Vo. IP), all the conductors are parallel, rather than arranged in twisted pairs. For carrying a single voice signal, this is fine. But if you have many signals in the same cable (as in the thick cables that serve an entire office), you would hear other people's conversations if these cables did not use twisted pairs. So, those thick cables always use twisted pairs. Look again at that phone cord. If you hold the two male connectors next to each other, facing the same way, you will see that the colors of the wires are in a different order. In fact, according to the spec for phone cords, they are always supposed to be . That is, whatever color wire is all the way to the left at one end of the cable, must be all the way to the right at the other end, and so on. OK, what about TP Ethernet cables? First off, the standard cables are all . But you cannot just connect all the wires straight- through; you have to pair them properly on the eight pins. The TP Ethernet standard says that the two pins closest to the center of the connector must be attached to the same twisted pair of wires. The next two farther out must connect to another pair. The others are different; the two all the way to the left are a pair, and the two all the way to the right are a pair. And the computers, switches, and other equipment have their female jacks wired to take this into the account. Note: they do make crossover Ethernet cables, which are used to connect, for example, two Ethernet switches together. If you look at one of these, you will see that the wire colors at the two ends are neither the same nor mirror- images of each other. Instead, they cross over so that the signals traveling along the cable in each of the two directions arrive at the right pins. STP CpuNetworkingKings. Bundling Ethernet Cable with the Cable Comb and Terminating a Patch Panel. Cross Talk Problems with Unshielded. What's the difference between an Ethernet cable and a UTP cable? My question is is there any major difference between UTP and STP cable in.
However, many modern switches can sense what is at the other end, and the type of cable, and compensate for it. One more thing: One of the differences between, say, a Cat 5 cable and a Cat 6 cable is that the Cat 6 twists more often and requires that the twist be maintained closer to the connector. This is one of the reasons it can handle the higher data rate. What is the result of all this? If you tried to use an Ethernet cable to carry a telephone signal, it might work. But if you tried to use a telephone cable to carry an Ethernet signal, it wouldn't work. So what about STP vs. While both can be used for Ethernet, UTP is much more commonly used, especially for new installations. The lack of shielding makes UTP less expensive and more flexible than STP, and the superior interference rejection of STP is usually not needed for acceptable performance. If you go to a computer store, you are much more likely to see UTP than STP, both in bulk cable (such as that intended to be installed inside a wall) and in patch cables which are sold with the connectors already attached.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
December 2016
Categories |